JOHNSON'S E-127 FLUX-'N-SOLDER with PURE TIN

Fastest Tinning of Bearing Shells and Most Common Metals

Johnson's E-127 Flux-'N-Solder with Pure Tin is the ideal blend of mild chlorides in paste form, mixed with pure tin powder to create a smooth, versatile tinning paste. It is widely used by many apparatus service shops for the pre-tinning bearing shells, prior to babbitting. Review Johnson's Technical Bulletin for more details and related products.

E-127 is also used for pre-tinning body steel before adding No. 523 Lead-Free Body Solder during the restoration of antique cars, or tractors. It is also used for pre-tinning parts which are later soldered into assemblies, to insure a full solder joint when using even mild, organic, or non-corrosive fluxes.

Johnson's E-127 has a melting temperature of 450°F and is compatible with all common solders, including lead-free alloys.  Residues are water soluble and should be removed after soldering.

ITEM SINGLE CASE NO. IN CASE SHIP WT.
1 lb Jar 16-02 16-03 12 14#
4 lb Jar 16-04 16-05 6 26#


JOHNSON'S E-128 FLUX-'N-SOLDER with PURE TIN

Fastest Sweating of Copper Tubes to Brass Fittings

Johnson's E-128 Flux-'N-Solder with Pure Tin is similar to E-127 but with slightly lower activation level to permit its safe use as a plumbing paste solder. When used properly by professional plumbers, this paste pre-tins as it fluxes, to pull the new Lead-Free Solders deeper into each joint. E-128 also has a smooth consistency that is easily applied to the outside of tubes and inside fittings, yet does not run or drip off parts.

Johnson's E-128 residues are water soluble and should be removed and flushed immediately after soldering.

ITEM SINGLE CASE NO. IN CASE SHIP WT.
1 lb Jar 16-62 16-63 12 14#


95/5 (Tin/Antimony) FLUX-'N-SOLDER

Widely Accepted for Lead-Free Plumbing with Compatible Solders

Johnson's 95/5 tin/antimony Flux-'N-Solder is a very smooth, non-leaded paste solder. In addition to being used for potable water systems, it is often used for soldering stainless steels, for high temperature or underground applications and where increased joint strength is necessary.

Like other Johnson Flux-'N-Solders, it is very easy to apply and holds in the joint to provide uniform pretinning when heat is applied. Melting temperature is 450 to 464°F. When tinning occurs, 95/5 wire solder should be applied to insure a full joint.

ITEM SINGLE CASE NO. IN CASE SHIP WT.
1 lb Jar 15-02 15-03 12

14#


JOHNSON'S 50/50 (Tin/Lead) FLUX-'N-SOLDER

Paste Solders Are Used In Many Industrial Applications

Many industrial uses still exist for this easy-to-use Flux-'N-Solder combination. Unlike E-127, this formula contains 50/50 powdered solder (50% lead),and therefore must not be used when soldering drinking water systems, food handling equipment, livestock tanks, etc.

Due to its relatively low melting temperature (360-420°F) and its rapid tinning action, this paste is excellent for soldering automotive components and other assemblies. Residues are water soluble and should be removed after soldering.

ITEM SINGLE CASE NO. IN CASE SHIP WT.
1 lb Jar 10-07 10-08 12 14#


JOHNSON'S 60/40 (Tin/Lead) FLUX-'N-SOLDER

Johnson's C-7 RA Type (Rosin Activated) Flux Formula

Johnson's 60/40 C-7 Rosin Flux-'N-Solder is an excellent medium-tech non-corrosive paste solder for electrical connections, and other easy-to-solder components. Melting range is 360-374°F.

ITEM SINGLE CASE NO. IN CASE SHIP WT.
1 lb Jar 13-02 13-03 12 14#


JOHNSON'S FLO-RITE PASTE SOLDERS*

Smooth Flux and Alloy Formulations

Johnson's Flo-Rite family of paste solders are engineered to provide a wide range of activation levels, temperature ranges and viscosities to meet today's production soldering requirements. Whether combined with non-leaded,or tin-lead solder powder, the result is always a smooth, dispensable paste solder that will compliment your soldering operation.

Typical applications include soldering automotive components, appliance manufacturing, ice making machines, pumps, valves and many other products. Residues are water soluble and are easily removed. Please tell us your requirements so we can blend the paste solder that is just right for your application.

F-610 is an active flux formulation that we stock in the following popular alloy combinations, while F-611 is less active for easier-to-solder components and where residues are more difficult to remove.

View our Technical Bulletin for this product.

ITEM SINGLE CASE NO. IN CASE SHIP WT.
4 Lb. Jar, 50/50 F610-87-5050-04 8 35#
1 Lb. Jar, 60/40 F610-87-6040-01 12 14#
1 Lb. Jar, 95/5 F610-87-9505-01 12 14#
1 lb. Jar, 50/50 F611-87-5050-01 12 14#

*Flo-Rite is a registered trademark of Kester Solder Company, Division of Litton Industries.